Samsung air error codes

Samsung air conditioners are fitted with a forward system of self-diagnostics, based on the results of which the system in case of a certain malfunction revelation blocks operation of the unit, simultaneously informing the user of the cause of a breakdown. One can remove errors of air conditioners with the help of a corresponding instruction on malfunction decoding. The instruction of the type can be found below.

Samsung AC030JXADCH air error codes

Air conditioners of the series Samsung AC0…JXADCH belong to the classical models of Samsung air conditioning equipment. They use R-410A refrigerant. This equipment consists of indoor and outdoor units, fuse and control. The air guide duct for this series is not provided by Samsung.

Error numberExplanation
E471Outdoor unit EEPROM Read/Write error (H/W)
E470Outdoor unit EEPROM Read/Write error (Option)
E202Communication error between indoor unit and outdoor unit (When there is no response from indoor units after tracking is completed)
E201Communication error between indoor unit and outdoor unit (Pre tracking failure or when actual number of indoor units are different from the indoor unit quantity setting on the outdoor unit) Error due to communication tracking failure after initial power supply (The error occurs with the failure regardless of the number of devices)
E203Communication error between outdoor unit inv - main micom (For PF #4~#6 controller, error will be determined from the time when compressor turns on)
E221Error on outdoor temperature sensor (Short or Open)
E108Error due to repeated communication address
E251Error on discharge temperature sensor of compressor 1 (Short or Open)
E231Error on outdoor COND OUT sensor (Short or Open)
E320Error on OLP sensor (Short or Open)
E485Error on input current sensor of inverter 1 (Short or Open)
E474Error on IPM Heat Sink sensor of inverter 1 (Short or Open)
E425Reverse phase or open phase
E422Blockage detected on high pressure pipe
E554Gas leak detected
E416System stop due to discharge temperature
E463System stop due to OLP temperature control
E458Fan speed error
E462System stop due to full current control
E404System stop due to overload protection control
E590Inverter EEPROM Checksum error
E464System stop due to DC Peak
E473Comp Lock error
E465Compressor overload prevention
E468Error on current sensor (Short or Open)
E461Error due to operation failure of inverter compressor
E467Error due to abnormal rotation of the compressor or unconnected wire of compressor
E469Error on DC-Link voltage sensor (Short or Open)
E472AC Line Zero Cross Signal out
E475Error of inverter fan 2
E660Error of inverter Boot Code
E500IPM over heat error on inverter 1
E484PFC Overload (Over current) Error
E466DC-Link voltage under/over error
E403Compressor down due to freeze protection control
E440Heating operation restricted at outdoor temperature over TheatJiigh value (default: 30 °C)
E441Cooling operation restricted at outdoor temperature below Tcooljow value (default 0°Q
E556Error due to mismatching capacity of indoor and outdoor unit
E557DPM remote controller option error
E198Error on thermal fuse of indoor unit (Open)
E121Error on room temperature sensor of indoor unit (Short or Open)
E122Error on EVA IN sensor of indoor unit (Short or Open)
E123Error on EVA OUT sensor of indoor unit (Short or Open)
E154Indoor fan error
El 53Error on float switch (2nd detection)
E508Smart install is not installed

Samsung ACC2400C air error codes

Air conditioners Samsung ACC2400C belong to the cassette-type air conditioners. This is the most successful option for rooms with suspended ceiling and a large area, they can be installed between the suspended ceiling and the usual one. Installation of this type of air conditioners is much easier than ща other split systems. The system of work of this air conditioning includes cooling and filtration of air and its feeding back through the distribution grids.

Error CodeMeaninqCheckina area
1Indoor unit thermistor sensor error- Indoor unit thermistor sensor
- PCB of the indoor unit
5Indoor unit pipe thermistor sensor error- Indoor unit pipe thermistor sensor
- PCB of the indoor unit
6Outdoor unit thermistor sensor error- Outdoor unit thermistor sensor
- PCB of the outdoor unit
9Float switch error- Drain pump, Float switch
- Drain system
- DIP switch(SW2) of the indoor unit (The No.2 and No.4 switches must be at “ON” position.)
AA Indoor and Outdoor communication error- Communication cables of indoor and outdoor units
- PCB of indoor and outdoor units
CWired remote controller communication error- Wired remote controller cables, Wired remote controller
- Main/Sub PCB of the indoor unit
DOutdoor pipe thermistor sensor error- Outdoor pipe thermistor sensor
- PCB of the outdoor unit

Samsung APH450PG air error codes

Air conditioners Samsung APH450PG are floor-mounted air-conditioning units. The refrigerant R-22 is used in the system of these air conditioners. Air conditioners have remote control, timer and air filter. There is a possibility of regulation of the air flow from such air conditioners. They are produced in a classical white color of the body frame.

Temperature displayCauseCorrective actions
E1Short of indoor temperature sensor
Open of Indoor temperature sensor
Check of departure of indoor temperature sensor
Check of PCB open/short
E5Short of indoor heat exchanger sensor
Open of indoor heat exchanger sensor
Check of indoor exchanger sensor departure
Check of PCB open/short
Replacement of sensor
E6Short of outdoor heat exchanger sensor
Open of outdoor heat exchanger sensor
Check of outdoor exchanger sensor departure
Check of PCB open/short
Replacement of sensor
E7Short of heater temperature sensor
Open of heater temperature sensor
Check of heater wiring diagram
Check of sensor attachment location
ELWhen the electrical heater is over heatedCheck of heater temperature sensor departure
Check of PCB open/shore
Replacement of sensor

Samsung AVXC1H022 series air error codes

Air conditioners of the series AVXC1H022 are cassette-type units. Samsung air conditioners of the cassette type are installed in spacious rooms with suspended ceilings. Due to the latest technology, the proportions of Samsung air conditioners are minimal ones. The presence of air conditioning in the room can be found not by the noise of operating equipment, but by the cool air. The air is evenly distributed in four directions.

Error No.(Ordered by priority)Error Meaning
E221Outdoor temperature sensor(Short or Open)
E251Digital comp.1 discharge temperature sensor(Short or Open)
E256Fixed comp.1 discharge temperature sensor(Short or Open)
E257Fixed comp.2 discharge temperature sensor(Short or Open)
E258Fixed comp.3 discharge temperature sensor(Short or Open)
E291High pressure sensor(Short or Open)
E296Low pressure sensor(Short or Open)
E271Comp.1 Sump temperature sensor(Short or Open)
E231COND OUT sensor(Short or Open)
E307Oil balance sensorl (Short or Open)
E308Suction sensor(Short or Open)
E311Double pipe sensor(Short or Open)
E425Reverse phase or missing phase
E452Instant power off error
E440Forbid heat mode operation when outdoor temperature is over 30°C
E442Forbid an operation during heat mode with refrigerant charging operation when outdoor
temperature is over 15°C
E443Start prohibition by refrigerant pressure error
E431Equal oil valve 1 self diagnosis
E202Communication error between indoor and outdoor unit (When not received in every room after completing the tracking)
E201Communication error between the indoor unit and outdoor uniL (Pre tracking failure or different unit number between set units and indoor units.)
E203Communication error between main of outdoor unit and sub MICOM or between units
E407Comp, down by high pressure
E410Comp, down by low pressure
E403Comp, down by the freezing protection control
E413Comp, down by the sump protection control
E554Loading failure
E416Comp, down by the discharge temperature sensor
E241COND OUT sensor breakaway
E269Suction temperature sensor breakaway
E453Fan motor hicfi temperature error
E454Fan motor RPM error
E455Fan motor IPM high temperature error
E458CT_over current
E457Fan motor reverse rotation error
E162Outdoor unit EEPROM error
E560Switch option setting error(rvot applied)
E428Comp down by compression ratio control
E121Room temperature sensor open or short error
E122Indoor unit EVAP IN Sensor open or short error
E123Indoor unit EVAP OUT Sensor open or short error
E154Indoor unit fan error
E124Communication error sends from indoor unit
E153Indoor unit floating S/V error(When 2“ detection)
P701Indoor unit floating S/V error(When 1“ detection)
E152Indoor unit EEV close failure(When 2“ detection)
P702Indoor unit EEV close failure(When 1“ detection)
E151Indoor unit EEV open failure(When 2 detection)
P703Indoor unit EEV open failure(When 1“ detection)
E128Indoor unit EVA IN sensor breakaway
E129Indoor unit EVA OUT sensor breakaway
E131Indoor unit heater sensor error
E265Digital compl Sump temperature sensor breakaway. Fixed compl Sump temperature sensor breakaway
E267Fixed comp2 Sump temperature sensor breakaway
E268Fixed comp3 Sump temperature sensor breakaway
E262Fixed compl Discharge temperature sensor breakaway
E263Fixed comp2 Discharge temperature sensor breakaway
E264Fixed comp3 Discharge temperature sensor breakaway
E456Fan motor over current error
E461CTJow current
ChProhibit starting during operation of the Crack case heater

Samsung IDH1800E air error codes

Air conditioners of the type Samsung IDH1800E have only one internal block. They have a centralized controller, which is installed on the wall. These units can also have a wireless remote controller with a display. However, it can be an optional accessory.

ERROR CODEERROR DESCRIPTION
ElIndoor unit room thermistor error
E5Indoor unit pipe thermistor error
E6Outdoor unit thermistor error
E9Float switch open error
EACommunication error between indoor unit and outdoor unit
ECCommunication error between wired remote controller and indoor unit
EDOutdoor unit pipe thermistor error
Reservation LED flickering(1Hz period)Indoor temperature sensor abnormal
Operation LED and reservation LED flickering (1Hz period)Indoor pipe temperature sensor abnormal
Operation LED and filter LED flickering (1 Hz period)Outdoor temperature sensor abnormal
Reservation LED filter LED alternating flickering (1Hz period)Float switch open abnormal
Reservation LED and filter LED flickering (1Hz period)Indoor and outdoor communication abnormal
Operation LED and reservation LED alternating flickering (1Hz period)Wired remote controller communication abnormal
Filter LED flickering (1Hz period)Outdoor pipe temperature sensor abnormal
1Indoor unit room thermistor error
5Indoor unit pipe thermistor error
6Outdoor unit thermistor error
9Float switch open error
ACommunication error between indoor unit and outdoor unit
CCommunication error between wired remote controller and indoor unit
DOutdoor unit pipe thermistor error

Samsung NX 1 air error codes

Samsung NX 1 is a mirrorless camera with interchangeable lenses. The front view of the camera is pretty standard. There are just l fixing mechanism of the lens and button of the repeater from the visible controls. There is a dust and moisture proof coating of the frame. The menu has a very wide selection of settings. The camera has a wide range of control interfaces for capturing and transfer of data. The camera is quickly and easily configurable.

Error messagesSuggested remedies
Lens is lockedThe lens is locked. Rotate the lens counter- clockwise until you hear a click, (p. 58)
Card Error• Turn off the camera, and then turn it on again.
• Remove the memory card and insert it again.
• Format the memory card.
Low BatteryInsert a charged battery or recharge the battery.
No Image FileCapture photos or insert a memory card that contains photos.
File ErrorDelete the damaged file or contact a service center.
Memory FullDelete unnecessary files or insert a new memory card.
Card LockedYou can lock SD, SDHC, or SDXC cards to prevent files from being deleted. Unlock the card when shooting, (p. 190)
Unable to capture a photo because folder and file number on the memory card reached the maximum values. Reset the folder number?File names do not match the DCF standard. Follow the on-screen instructions to reset the folder number.
Error 00Turn off your camera and remount the lens. If the message still appears, contact a service center.
Error 01/02Turn off your camera, remove the battery, and insert again. If the message still appears, contact a service center.

Back to Top